AAAAAA
Results:
1-14
|
Results: 14
Authors:
CERVENKA A
AJROLDI G
MAUER FHJ
ALLAN PS
Citation: A. Cervenka et al., CHARACTERIZATION OF FINITE FIBER-LENGTH COMPOSITES - PART III - STUDIES ON THIN-SECTIONS EXTRACTED FROM MOLDINGS (WAFERS) (TECHNICAL REPORT) (VOL 69, PG 1725, 1997), Pure and applied chemistry, 70(2), 1998, pp. 1
Authors:
KALAY G
ALLAN PS
BEVIS MJ
Citation: G. Kalay et al., SHEAR CONTROLLED ORIENTATION, Kunststoffe, Plast Europe, 87(6), 1997, pp. 768
Authors:
REIS RL
CUNHA AM
ALLAN PS
BEVIS MJ
Citation: Rl. Reis et al., STRUCTURE DEVELOPMENT AND CONTROL OF INJECTION-MOLDED HYDROXYLAPATITE-REINFORCED STARCH EVOH COMPOSITES/, Advances in polymer technology, 16(4), 1997, pp. 263-277
Authors:
CERVENKA A
ALLAN PS
Citation: A. Cervenka et Ps. Allan, CHARACTERIZATION OF FINITE-LENGTH COMPOSITES .1. INTRODUCTORY PAPER, Pure and applied chemistry, 69(8), 1997, pp. 1693-1705
Authors:
GLAS L
ALLAN PS
VUKHANH T
CERVENKA A
Citation: L. Glas et al., CHARACTERIZATION OF FINITE-LENGTH COMPOSITES .2. MECHANICAL PERFORMANCE OF INJECTION-MOLDED COMPOSITES, Pure and applied chemistry, 69(8), 1997, pp. 1707-1723
Authors:
CERVENKA A
ALLAN PS
Citation: A. Cervenka et Ps. Allan, CHARACTERIZATION OF FINITE-LENGTH COMPOSITES .3. STUDIES ON THIN-SECTIONS EXTRACTED FROM MOLDINGS (WAFERS), Pure and applied chemistry, 69(8), 1997, pp. 1725-1740
Authors:
ALLAN PS
CERVENKA A
MOORE DR
Citation: Ps. Allan et al., CHARACTERIZATION OF FINITE-LENGTH COMPOSITES .5. MODELING OF STIFFNESS, Pure and applied chemistry, 69(8), 1997, pp. 1741-1751
Authors:
VONBRADSKY GJ
BAILEY RS
CERVENKA AJ
ZACHMANN HG
ALLAN PS
Citation: Gj. Vonbradsky et al., CHARACTERIZATION OF FINITE-LENGTH COMPOSITES - PART IV - STRUCTURAL STUDIES ON INJECTION-MOLDED COMPOSITES, Pure and applied chemistry, 69(12), 1997, pp. 2523-2539
Authors:
ALLAN PS
BEVIS MJ
GIBSON JR
MAY CJ
PINWILL IE
Citation: Ps. Allan et al., SHEAR CONTROLLED ORIENTATION TECHNOLOGY FOR THE MANAGEMENT OF REINFORCING FIBERS IN MOLDED AND EXTRUDED COMPOSITE-MATERIALS, Journal of materials processing technology, 56(1-4), 1996, pp. 272-281
Authors:
HINE PJ
DUCKETT RA
WARD IM
ALLAN PS
BEVIS MJ
Citation: Pj. Hine et al., A COMPARISON OF SHORT GLASS-FIBER-REINFORCED POLYPROPYLENE PLATES MADE BY CONVENTIONAL INJECTION-MOLDING AND USING SHEAR CONTROLLED INJECTION-MOLDING, Polymer composites, 17(3), 1996, pp. 400-407
Authors:
WANG L
ALLAN PS
BEVIS MJ
Citation: L. Wang et al., ENHANCEMENT OF INTERNAL WELD LINE-STRENGTH IN THERMOTROPIC LIQUID-CRYSTAL POLYMER MOLDINGS, Plastics, rubber and composites processing and applications, 23(3), 1995, pp. 139-150
Authors:
KALAY G
OGBONNA C
ALLAN PS
BEVIS MJ
Citation: G. Kalay et al., THE MANAGEMENT OF MICROSTRUCTURE IN SEMICRYSTALLINE POLYMERS, Chemical engineering research & design, 73(A7), 1995, pp. 798-809
Authors:
OGBONNA CI
KALAY G
ALLAN PS
BEVIS MJ
Citation: Ci. Ogbonna et al., THE SELF-REINFORCEMENT OF POLYOLEFINS PRODUCED BY SHEAR CONTROLLED ORIENTATION IN INJECTION-MOLDING, Journal of applied polymer science, 58(11), 1995, pp. 2131-2135
Authors:
ALLAN PS
BEVIS MJ
Citation: Ps. Allan et Mj. Bevis, SHEAR CONTROLLED ORIENTATION IN EXTRUSION, Plastics, rubber and composites processing and applications, 16(2), 1991, pp. 133-137
Risultati:
1-14
|