AAAAAA

   
Results: 1-13 |
Results: 13

Authors: Bouzakis, KD Michailidis, N Hadjiyiannis, S Pavlidou, E Erkens, G
Citation: Kd. Bouzakis et al., An effective way to improve the cutting performance of coated tools through annealing, SURF COAT, 146, 2001, pp. 436-442

Authors: Bouzakis, KD Michailidis, N Hadjiyiannis, S Efstathiou, K Pavlidou, E Erkens, G Rambadt, S Wirth, I
Citation: Kd. Bouzakis et al., Improvement of PVD coated inserts cutting performance, through appropriatemechanical treatments of substrate and coating surface, SURF COAT, 146, 2001, pp. 443-450

Authors: Bouzakis, KD Michailidis, N Erkens, G
Citation: Kd. Bouzakis et al., Thin hard coatings stress-strain curve determination through a FEM supported evaluation of nanoindentation test results, SURF COAT, 142, 2001, pp. 102-109

Authors: Bouzakis, KD Lontos, A Kechagias, V
Citation: Kd. Bouzakis et al., Creep behaviour prediction and optimum design of plasma sprayed coatings with intermediate bonding layer, SURF COAT, 142, 2001, pp. 283-289

Authors: Bouzakis, KD Michailidis, N Vidakis, N Efstathiou, K
Citation: Kd. Bouzakis et al., Failure mechanisms of physically vapour deposited coated hardmetal cuttinginserts in turning, WEAR, 248(1-2), 2001, pp. 29-37

Authors: Bouzakis, KD Vidakis, N Lontos, A Mitsi, S David, K
Citation: Kd. Bouzakis et al., Implementation of low temperature-deposited coating fatigue parameters in commercial roller bearings catalogues, SURF COAT, 133, 2000, pp. 489-496

Authors: Bouzakis, KD Michailidis, N Vidakis, N Efstathiou, K Leyendecker, T Erkens, G Wenke, R Fuss, HG
Citation: Kd. Bouzakis et al., Optimization of the cutting edge radius of PVD coated inserts in milling considering film fatigue failure mechanisms, SURF COAT, 133, 2000, pp. 501-507

Authors: Bouzakis, KD Koutoupas, G Siganos, A Leyendecker, T Erkens, G Papapanagiotou, A Nikolakakis, P
Citation: Kd. Bouzakis et al., Increasing of cutting performance of PVD coated cemented carbide inserts in chipboard milling through improvement of the film adhesion, considering the coating cutting loads, SURF COAT, 133, 2000, pp. 548-554

Authors: Bouzakis, KD Lontos, A Vidakis, N David, K Kechagias, V
Citation: Kd. Bouzakis et al., Determination of creep behaviour of monolayer thick plasma sprayed coatings, by means of the impact test and an analytical FEM supported evaluation procedure, THIN SOL FI, 377, 2000, pp. 373-381

Authors: Bouzakis, KD Vidakis, N
Citation: Kd. Bouzakis et N. Vidakis, Superficial plastic response determination of hard isotropic materials using ball indentations and a FEM optimization technique, MATER CHAR, 42(1), 1999, pp. 1-12

Authors: Bouzakis, KD Kouremetis, A Giannaros, K
Citation: Kd. Bouzakis et al., Time schedule for the replacement of corroded rotary kiln sections based on measurements and calculations, ZKG INT, 52(8), 1999, pp. 443

Authors: Bouzakis, KD Vidakis, N Michailidis, N Leyendecker, T Erkens, G Fuss, G
Citation: Kd. Bouzakis et al., Quantification of properties modification and cutting performance of (Ti1-xAlx)N coatings at elevated temperatures, SURF COAT, 121, 1999, pp. 34-43

Authors: Bouzakis, KD Vidakis, N David, K
Citation: Kd. Bouzakis et al., The concept of an advanced impact tester supported by evaluation software for the fatigue strength characterization of hard layered media, THIN SOL FI, 356, 1999, pp. 322-329
Risultati: 1-13 |